3.8 liter engine out of a 1989 Oldsmobile Delta 88. Ran ok when taken out of the car several years ago.
I AM IN NEED OF A USED ENGINE FOR MY 2006 FORD MUSTANG. I NEED A 4.0 V-6 FORD ENGINE.I WANT IT AS COMPLETE AS POSSIBLE AND WOULD LIKE TO HEAR IT RUN IF AT ALL POSSIBLE PRIOR TO BUYING IT.MILES UN-IMPORTANT AS LONG AS IT IS TROUBLE-FREE.CALL ME WITH WHAT YOU HAVE. SERIOUS BUYER AND CAN MEET WITH MINIMAL NOTICE - JUST CALL.THANK YOU. JOHN
87 305 tune port engine and trans pulled from a formula firebirdcomplete with harness and accessoriesfits 86 - 92 firebird and camaro
I have for purchase if ad is visible.1 Rear Passenger door window regulator motor. Ready to install. I do have for additional cost, the window that came with it.This ad price is for the regulator only.Taken off my personal car door. I know it works wellDoor was damaged at bottom near rocker and whole door was replaced. Price firm and cash onlyPlease reply with your name and number if you want r...
New, Ready to run, Dart SHP 400 Small Block Engine, Dart Special High Performance (SHP) 400 (4.125 Bore) Ductile Iron Block Dart Iron Eagle 23 230cc Angle Plug Cylinder Heads Scat Cranks 6.0" Connecting Rods Comp Cams Hydraulic Camshaft: (305 Duration) (.525 Lift) (3500-7200 RPM) Comp Cams Chrome Moly Roller Rockers (1.52 Ratio) Dart Single Plane Intake (3500-7500 RPM) MAHLE Flat Top Forged Pis...
This block has about 125,000 miles on a .030 overbore. It has a sleeve installed in cylinder 4 that was in there for the entire 125k with no problems at all. The engine was run in my daily driver vehicle until the vehicle was scrapped after an accident. The engine was still in very good running condition at that point. I recently tore it down with the intention of doing a ring job and selling i...
This engine has over 100,000 miles on it. It was running when the pickup it was pulled from was scrapped due to terminal rust. Its missing a few components but the short block is intact and not stuck. I still have the front cover, intake, etc. and other components if you want them. Hoping someone can use some of the parts. Otherwise it will have to be scrapped. $50 takes everything. Contact me ...
Selling some 90-92 camaro firebird 3.1 v6 motor parts i have a brand new oil pan,timing gears, oil pump and screen, oil pan gaskets,valve cover gaskets, intake and etc gaskets to start rebuilding a motor all the gaskets are quality fel-pro everything is brand new never been touched had a brought and sold it asking $50 or best offer for all call .
over a month agoFt Wayne, IN+17 milesAuto Parts for Sale
I have three different engines - Cavalier, Grand Am, and Bronco, . they have the tranny, alternator, starter and wiring with them. $150.00 and you can have the one you want with the tranny and all the acc. OR - $400.00 you can have all three CLEANING OUT THE SHOP these are engines pulled out of running cars, not new, buy as you choose these engines all turn over by hand and have been stored ins...
over a month agoFt Wayne, IN+17 milesAuto Parts for Sale
1970 DodgePlymouth 340 small block engine - disassembledBlock is in pristine original condition having never been damaged, repaired, or board outThis engine has been in storage since mid 70sEngine has been hot tanked and honed onlyComes with original 101 pistons with new hastings ringsOriginal crank, exhaust manifolds, engine internals, all assembly bolts, etc.Aluminum timing belt housingTwo ha...
GM 350 block bored .030" over Block decked to 9.013" case height ARP Main bolts SpeedPro forged pop up pistons 12.5 to 1 compression File fit rings Scat 5.7" bushed rods GM steel crank "1182" turned .010/.010 SpeedPro Main bearings/King Rod bearings PowerBond/Dayco damper Champ CP57LT oil pan & pickup Melling Select oil pump World Prod Sportsman 2 heads Manley head bolts Beehive springs w/Comp ...
Fresh 406 cubic inch SBC with 817 block Bored .030' over, honed w/torque plates ARP main studs/Manley head bolts Block decked square, 9.005" case height Eagle forged crank, 3.750" stroke Eagle 6" H-beam rods, 8740 rod bolts Mahle PowerPak pistons, 11.6 to 1 File fit rings 1mm, 1mm, 2mm package RHS iron heads, 235cc runners, 64cc 2.08 seven mm intakes/1.60 ti exh vlvs Titanium retainers on Howar...